The single most damaging mistake in industrial coatings is not a bad product. It is a good product applied against the instructions on its own technical data sheet. Pot life ignored, film thickness guessed at, recoat window missed, surface prep skipped: each one shows up later as peeling, blistering, or premature corrosion on steel that should have lasted for years. For fabricators and facility crews across Alberta, learning to read a data sheet properly is a skill that protects every coated asset. Legacy Coatings supplies industrial coatings across Western Canada, and this is the walkthrough the technical team gives most often.
Start With Surface Preparation and Substrate
Before any number about the coating itself, a good data sheet specifies what the surface must look like before application. That usually means a required cleanliness standard, an anchor profile, and acceptable conditions for the substrate.
If the sheet calls for a specific profile and your blast does not achieve it, the coating cannot grip and will fail no matter how well you spray it. Prep is not the step before the real work; on a data sheet it is the foundation the warranty rests on.
The Numbers That Decide Pass or Fail
Dry film thickness (DFT)
DFT is the specified thickness of the cured coating, usually given as a range with a minimum and maximum. Too thin and you lose protection; too thick and you can trap solvent or cause cracking. The sheet also lists the wet film thickness to target so you hit the correct DFT, and volume solids, which tell you how much of what you spray stays on the surface.
Pot life and induction time
For multi-component coatings, induction time is the wait after mixing before the product is ready to spray, and pot life is how long the mixed material stays usable. Spray past pot life and you are applying a product that is already curing in the pot, which wrecks flow and adhesion. These are hard limits, not suggestions.
Recoat window and cure times
The sheet lists a minimum and often a maximum time before the next coat. Miss the maximum and you may have to abrade for adhesion. It also lists cure-to-handle and full-cure times, which govern when the asset can go back into service.
Read the Conditions Those Numbers Assume
Every figure on a data sheet assumes a reference temperature and humidity. In an Alberta shop or on a cold site, your real pot life, flash, and cure times can differ sharply from the printed values. The sheet typically shows how the numbers shift with temperature, and a lower temperature almost always means longer cure and sometimes a different thinner. Matching products and thinners to real conditions is where a supplier earns its keep, and the industrial coatings team at Legacy Coatings helps clients translate reference numbers into what will actually happen on their project.
Turn the Data Sheet Into a Repeatable Spec
The best crews build a short job spec straight off the sheet: prep standard, mixing ratio, induction time, wet and dry film targets, recoat window, and conditions. Keeping the current sheets for your whole system on file, available alongside the full coatings product range, means every applicator works from the same numbers. For teams that want formal grounding in reading sheets, mixing, and application, industrial coating training turns that knowledge into shop-wide habit.
Frequently Asked Questions
What is the difference between pot life and recoat window?
Pot life is how long a mixed multi-component product stays sprayable before it starts curing in the pot. The recoat window is how long after applying one coat you can apply the next with good adhesion. They are separate clocks and both matter.
Why does dry film thickness have a maximum, not just a minimum?
Because too much film can trap solvent, sag, or crack and can actually reduce performance. The range on the sheet is the zone where the coating performs as designed, so you target both the minimum and the maximum.
Do data sheet times apply in a cold Alberta shop?
Not directly. Printed numbers assume a reference temperature and humidity. Lower temperatures extend pot life, flash, and cure, and may require a different thinner. Always adjust the printed values for your real conditions.
What is induction time and can I skip it?
Induction time is a required wait after mixing certain products so the components react before spraying. Skipping it can hurt flow and adhesion, so treat it as a mandatory step when the sheet lists one.
Where do I get current data sheets for my coatings?
From your supplier. Legacy Coatings can provide the technical data sheets for the industrial systems it supplies and help interpret them for your substrate and site conditions.






